Recent content by omega11

Hi all, I had our Texecom Elite 48 working with SmartCom and we were getting notifications in the Texecom app, butr after adding ComGSM we're not getting any notifications via the Texecom App nor via SMS. I know both are working as I can connect to the panel both via SmartCom and also sending...

Hello, I have a Valliant ecotec plus bioler that is contsantly running. Not heating, but just you can hear it running. This is a new thing and not quite sure what is wrong with it. It works fine when heat is called from the thermostat, but then it just runs forever. It's as if it is an overrun...

OK, got it working, as you suggested, I had to move ComIP to com3 and then use com2 for ComGSM and com3 for ComIP instead. Seems to be working now as I'm getting SMS! Many thanks!

Firmware is 6.05.03LS1 The panel doesn't have a com3, only com1 and com2. The ComGSM is connected to the digi modem via the adaptor.

@sparkymarka thanks! So I have been able to connect it up to the Digi Port with the adaptor and it seems to be happy and working (all the right LED's are on), but I cannot seem to assign it in the panel. If I go to Comms (in Wintex) and then Com Port Options, I'm assuming that I need to set...

HI, Quick question and I'm guessing the answer, but is it possible to connect both a SmartCom AND a ComGSM to a Texecom Elite 48 panel? I'm guessing not because both of the coms ports are taken up by the SmartCom, but I thought I'd ask. If it IS possible, how would it be done? Thanks in advance.

Thank you all for your help. After speaking with Texecom, we both came to the conclusion that there may be a problem with the SmartCom deci e. I purchased a new one and it worked first time. I'm assuming that the original suggestion that the device was too old for some reason was true...

Hi all, thanks for all your help so far. OK, on site now and I can confirm the following... - Premier Elite 48 Firmware version is : 6.05.03LS1 (recently flashed) - SmartCom CEL-0001 firmware version is 3.0.21 (Hardware revision 21) - Wintex Version is : 8.2 I have the SmartCom connected and...

@sparkymarka OK thanks, will check properly on Monday when I have physical access to it. Would it need to be updated further? Is there a way to check it's actual firmware remotely? As I have access to Wintex I could check it now. Assuming it is v3, I still need to find out why it can't...

Hi, that's very kind of you, thank you. Unfortunately, I'm not near the panel until Monday, I have the lead (USB-com) and can connect to it via the lead or via the smartcom using the IP address IP using Wintext, so all that part works, it just doesn't seem to be able to contact Texecom for the...

I just checked the ebay listing and apparently it's a v3 (I haven't personally checked the unit as I'm away until Monday). Assuming its a v3, does that mean I can upgrade the firmware on it? If so, do you know how? Thanks again.

It's version 6.x (can't recall what the x is right now, but it was the latest version available) I'd agree, but I (wrongly) assumed that SmartCom was SmartCom, seems a bit bad that there are versions of it that won't work/not supported due to a version issue that can't be flashed... In terms of...

@sparkymarka thanks for your responses, i appreciate it. Quick question ahead of me checking the SmartCom version on Monday, is there no way at all to firmware update them? I assumed purchasing a SmartCom device it would work with the panel, or if not, they could both be upgraded to work...

OK thanks, I'll not be able to check until Monday. Could it be a SmartCom firmware version that it's not working?

Hi, I got it from ebay, not sure of the software version, how would i connect to it to find out? If I go to the IP address of the device I don't get anything...