joinery

I have an disused outbuilding (approx 10m x 3m) which I'd like to turn into something useful like a workshop/office/gym/etc. The building has a truss roof and currently there is no internal ceiling i.e. the trusses are all exposed. I could put a regular flat ceiling in, but the height would be...

Hi all, I'm looking to replace the bottom section of this wooden window frame illustrated in the pic. It would guess that that each section of 4 panes has been fitted within the larger frame. I want to remove the left hand section of 4 panes for ease of repair. The question is, does anyone know...

Hi - I’ve been attempting to buy and put together oak fittings to house a glass balustrade and just looking for some advice (from those with more experience than me!), in how best to connect up the handrail most securely where it meets the ceiling of the ground floor. I have but Baserail in and...

I cannot get my head around how I’m going to do this! Ideally I want the wall plate sat back so it isn’t exposed too low. Structural engineer said I can do it either way, sit on top of shorter beam coming out of extension or sat on the post, I can’t see how it would work on picture one? Can...

Ideally I want the wall plate sat back so it isn’t exposed too low. Structural engineer said I can do it either way, sit on top of shorter beam coming out of extension or sat on the post, I can’t see how it would work on picture one? Can anyone help, what’s the best way to go about it? If I did...

Hello, We had out kitchen fitted last November, and as the year has gone on we've spotted several issues. The worst (or the one that seems to be driving my wife crazy) is that the worktop joints aren't level. It's a U shaped kitchen and both connecting joints seems to be raised. Is this an...

My next DIY project is replacing naff cheap late 70s horizontal bannisters for new traditional spindle handrail version You can see the bottom of the stairs and stringer in picture 1 and the newly post I'm getting in picture 2. From the various videos I have watched on the topic I am thinking...

We need to repair a couple of holes in chipboard flooring which is laid on engineered i-joists. Do you have any advice on how to support the square edges of the new chipboard pieces given the nature of i-joists? Unfortunately it is unclear to us how to attach support/noggins to these joists...

Hi all, Hope you’ll be able to help. I’m getting the hallway and stairs of my new house replastered and realised we’ll have to sort out the door frames too prior to plastering. Not sure if the architraves need replacing too? They're all just a bit beaten up through a lack of maintenance and...

Hi Currently getting my bathroom done and I let the person know I wanted the old architraves removing and new ones fitting eventually because I’m getting new doors put in at the end of the month… only thing is, they have tiled right up to the frame with only a small gap? And the wall is half...

Hi Everyone, This thread has been invaluable to me the last few weeks. We have had an ongoing, 5 month saga with a B&Q kitchen fitting. The first fitters that attended were clearly not qualified and did virtually everything wrong. This needed to be assessed and refitted. The work included not...

Hi Everyone, This forum has been invaluable to me the last few weeks and I really appreciate all of the help I’ve been given regarding a variety of issues. We had a kitchen fitting with B&Q that has been plagued with issues for the get go. It’s now over four months since the fitting started...

Hoping someone can help with their opinion on this. We have had endless issues with B&Q appointed fitters. We initially had fitters that had been chucked off the job (by B&Q) because they didn’t know what they were doing - they had fitted cupboard units to the back wall. We were then given new...

Hoping someone can help. I recently had a B&Q kitchen installed (by their fitters) and there is a fairly sizeable gap between the hob and wooden worktop (image attached). The fitters have said they can’t get the hob any tighter but to me the gap seems too big. Could anyone please advise if a...

I am almost there with my self build entertainment unit and noticed today a issue that I was hoping wouldn't (wistfully) wouldn't occur. The inner vertical of the shelving units on either side are causing a slight bowing of the counter top. The counter top is 2x18mm boards and the verticals on...

I'm removing a section an old airing cupboard and will be closing the opening with a stud wall. I've had an engineer give me the thumbs up on removing it. The stud wall will be plasterboarded and tiled and a radiator and cabinet will be installed on it. The existing cupboard wall is made from...

Hi What thickness of MDF do people recommend for a storage unit. It will be self supporting off the floor and fit onto a end wall measuring 3m x 2.4m. The base unit including the circulation space behind will be about 600mm deep, the cupboards and shelves etc. above will be set back and total...

Looking for some advice - having my kitchen redone and the b and q plan shows this cut of the worktop. The sink is as shown. The fitter didn’t look at the sink until after they cut the worktop and then told me I can’t have my sink (or any sink more than 780mm). I can’t find any standard bowl...

Hi all. I'm new here, please go easy on me. I need you all the chippys, architect and builders advice on board and ASAP. I've removed my chimney breast walls from top to bottom. I'm now left in the bedrooms with exposed Joists, which are 7x3 timber and 5 metres long. I was hoping, is it...

hi I bought a new oven and now my cabinet door is hitting off the oven handle. I looked online and saw you can buy restrictors but my hinges look different to the ones online. Can anyone give me some advice please. I have posted a couple of pictures which I hope demonstrate what I am on...