Delta T rating help

[owenjt]

I'm renovating my house and am having a new heating system installed. The plumbers are planning to install a Vaillant ecoFIT pure combi 30kw high efficiency combi boiler but I'm struggling to get an answer on what Delta T rating I should be looking at when choosing my radiators.

I've asked a number of people including the plumber and Vaillant themselves and have had a different answer from everyone, ranging from T30 to T50. Please can anyone help me find the correct rating?

 

[Madrab]

Depends on a few things but primarily what the target system temp it will be running at and what heat loss has been calculated so radiators can be sized correctly.

T50 is the rad makers standard but new regs now state that new systems should be run @ 50deg dropping the delta, hence why T30 is now talked about, that tends to mean that rads need to be increased in size to achieve the required output to meet the rooms heat loss calcs.. Some manu's are now catching up with 2 output ratings, T50 and T30. There are tables that allow conversion to be made but going from T50 to T30, then the output would be approx 50% less (Output x 0.51)

So what your system will run @ is the what needs to be known, talk to your installer.

 

[owenjt]

Thank you. So if the delta depends on the target system temperature and new systems should be run at 50°, then the delta rating would be quite low as you have to take the average from the temperature of the water going into the radiator and coming out of the radiator minus 20° (the average room temperature).

To achieve T30 the average in/out temperature would have to be 50° which means the target temperature would have to be higher.

I'm guessing you work things out based on the worst-case scenario, e.g. what target temperature you might set in winter?

 

[vulcancontinental]

You shouldn't really be offered a choice as the Building Regulations for new systems stipulate radiators should be sized for a heat pump temperature regime even if a boiler is being installed so it's a straight swap later.

Emitter surface 50 degrees, internal air temperature 20 degrees, delta T 30 degrees.

 

[Bigily87]

ask @CBW
He knows his stuff

 

[Johntheo5]

It may be prudent to size on a T30 basis for future proofing, heat pump etc, you would then have to oversize by a factor of almost X2, (50/30)^1.3, 1.94.

 

[owenjt]

It may be prudent to size on a T30 basis for future proofing, heat pump etc, you would then have to oversize by a factor of almost X2, (50/30)^1.3, 1.94.

Thing is you can end up with huge radiators then. Need to find the right balance between the size of the radiator and what temperature you'd need to run the boiler at.

 

[Deleted member 267285]

ask @CBW
He knows his stuff

Unfortunately not on this stuff, but thanks.

 

[Madrab]

I'm guessing you work things out based on the worst-case scenario, e.g. what target temperature you might set in winter?

Delta's are set on a 20Deg standard, that being the considered the optimum room temp. Hence rads are set on a average rad temp of 70Deg and an air temp of 20Deg, hence a delta of T50. UK manu's used to actually be T60 (80deg/20deg) but aligned to Europe's T50 about 10 odd years ago.

New BR standard is now Average rad temp of 50deg with an air temp of 20Deg, so DeltaT is now T30, as suggested, to come into line with lower flow temps of G/ASHP and to drive down fossil fuelled boilers temps to reduce consumption.

Problem is large numbers of manufacturers still quote their output at T50, so a conversion needs to be applied - difference between T50 and T30 is 0.51 so a T50 rads output needs to be multiplied by 0.51 to provide the T30 output. That then needs to be aligned with the rooms heat loss calc to arrive at the correctly sized rad. Always best to check with the manufacturer what their outputs are ranged at, if not on the tech sheet, e.g. stelrads standard are @ T50.

 

[Madrab]

ask @CBW
He knows his stuff

Ooooo .....