sparkymarka

T

• T

  Tboyy

• 20 Mar 2022

Hi I have a pyronix enforcer alarm it's been working fine last couple yrs but for the last couple of days it randomly starts setting night set or it will say kitchen pir alarm input then starts setting night set is there something I can do thx

• 

  sparkymarka

• 8 Apr 2021

Is it an 700/800l control panel ?

• 

  Carl Smith

• 8 Apr 2021

Hello, I've recently moved in to a house that has an c001-102 intellisense panel by the front door, I've opened it and the tamper thing is now on eternally, I have removed the 12v supply to stop the noise but was wondering if there is a code to reset the whole thing as no-one left any codes to enable me to use the alarm. I am sorry to bother you, but any help would be gratefully received. Cheers Carl

• 

  Delaneye

• 21 Mar 2021

Hi Sparky,
I am looking for some help please. We moved into our house in September, we was given fobs for the alarm but no passcode.
We had some work done and the work men discounted the internal alarm pad since then there is a orange light next to the warning symbol.
If I scan the fob it says
“ 1 problem(s)”
Set ?
And then if u try a code it says
Call installer
9651

D

• D

  david mclaren

• 12 Oct 2020

Help
Intelliserve c023-203 iss1

My sister's alarm panel has a high pitched noise and for is flashing

Can you give any help at all as I saw your post from 2012

Many thanks either way

David

A

• A

  Alex Bedford

• 22 Aug 2020

Hello Sparky Mark, Hope you can give a few moments thought to help me? We have a Scantronic 9448. No mains power on the green LED. I checked output voltage from transformer and it was zero, 240v in was OK. I fitted a replacement transformer which gives 19v into the circuit board. But the power isn't getting to the LED (or the buzzer?). All three fuses on the board are fine. Hope you can help me.

D

• D

  D_Ward

• 10 Aug 2020

Hi. I have been informed that you may be able to assist with a thread I have just posted. Any help appreciated. Cheers.

https://www.diynot.com/diy/threads/elvox-801-to-elvox-8870-6-wire-system.550666/#post-4705208

• 

  OliverMax

• 14 Jul 2020

Hi, I was wandering if you could help me? I’ve got a Pyronix Enforcer that needs a new pir connecting to it but the engineer that installed it has gone awol! I’ve seen you know how to default without the engineers code?? I’ve read all the manuals to no avail and I’m getting desperate! Thanks!

• 

  AB181184

• 5 Jul 2020

Hi I was, wondering if you could help, me I've got a, euro sec alarm and I changed a, battery in my pr sensor in my kitchen now the alam wont set and the control panel kitchen!!!!!! Check!!!!!! Can figure it out at all any info that might help would be much appreciated
Regards Adam

A

• A

  Adrian McDonnell

• 2 May 2020

Hi Mark,
Hope you don’t mind me contacting but I can see from post that you have known on Scantronic 9448.

Basically I don’t have the user code for my 9448 alarm so I’m assuming it’s still at default 1234. So I just wanted to check before I use the use guide that when I go through the procedure of changing the user code that the alarm won’t go off if user code is not the default number?
Adrian

J

• J

  James Frost

• 26 Mar 2020

It's the external bell that contains strobe light outside my house. Maybe called it SCB.
Connected as follows, 12v to 12v, strobe to strobe,OV to OV, This is were I have gone wrong, Bell to Trig then tamp to bell?
Now rectified, now wired bell/bell and tamp/trig. I am still left with a 'Tamper Fault Lock Out' message on my keypad.

• 

  Elliotti

• 27 Feb 2020

Hello, I’ve recently moved into a new house with a Eurosec alarm and previous owners forgot the code. I’ve seen you’ve helped people with this before was wondering if you wouldn’t mind helping me. Cheers Alex

• 

  DigitalG

• 23 Feb 2020

Hi, I see from one of your posts that you managed to default a Pyronix Enforcer? My brother in law’s alarm guy has gone awol and I need to default the alarm as none of the default codes work. Do you know if there is a way to do this?

Cheers

Andy

J

• J

  Jjash

• 5 Jan 2020

Hi sparky, I wonder if you could help me. I've tried everything. I've got the EuroSec Cp8l alarm and getting the error, service due. I've moved into this house and have no contact with the engineer who fit the alarm. No engineer code etc. How can I remove this error to get the alarm back to normal please. All I know is the user alarm code.

Thanks,

James

L

• L

  Lea27

• 19 Oct 2019

Please help- we are setting up enforcer v10 in a bungalow with one door. We do not need different zones as day/night settings the same- all alarms set. We ‘learned’ door sensor but there was message ‘mismatch 07’. What should the settings be for only entrance exit. control panel is at front door. No internal sensors. Thanks!