electrics

Hi, I’m fitting a kitchen but the cooker point where it will be connected to is a bit high for the backing rail. Im wondering if I can either cut a bit out of the rail, (seems a bit too structural to do this ? or move the rail a bit lower ? or do I need to get the electrics moved ?

Hello, Does anyone know how to change the bulb in this type of downlight fitting. I just couldn't figure it out. I've tried all sorts including twisting, pulling and nothing works. I've taken photos of it from every direction. Need help please.

I’m in the middle of replacing a cracked electric hob with an induction hob. I’ve removed the old hob- it appears to have the twin and earth supply cable hard wired into the hob. There is no junction box visible. The replacement hob comes with an attached cable. On removing the covering plate...

Hi, we have a HiB bathroom cabinet with light, demisting, usb and shaver charger points. All of these have stopped working bar the shaver charging point. Its just over a year old. Any pointers as to what may have failed, seems odd that the shaver point still has power but nothing else has...

Hi all, I have just bought a house and currently removing the kitchen to replace and fit oven/hob. We would like to install a gas hob and electric oven (integrated) The kitchen does not have a dedicated cooker circuit. Below is a picture of what we have. My question is.... if I got an...

I am replacing the extractor fan in the kitchen. It has a fused isolator switch. When i switched it off to be able to get to the extractor fan safely, the 8 LED ceiling lights start to flicker. Switch the isolator back on again and flicker stops! There is no dimmer on the LED lights, just an...

Hi, i am hoping someone can help. I tried taking a look at my Neff Oven Fan element ( Neff B1432N2GB/01) since the RCD kept tripping everytime it was switched on after about 30 seconds so I brought a new element. Now when taking the old one off I pulled too hard stupidly and now I’m not sure...

Can I just ask when you have two sockets with with about a few cm in between how do you plaster or fill in between them or does the face of the sockets cover them. The thing I am referring to is I have a two gang socket then a small gap about a cm or two and then an Ariel socket. There needs to...

Weird one and was wondering if anyone can help? I originally booked for an electrician to come and have a look but had to cancel due to being in isolation for 12 weeks (fun). Can anyone give me any ideas on what this might be? Electrician said it could just need a new pull cord switch in the...

Hi, new member here, but not new to DIY by a long shot. Bit of an embarrassing one this, given I am an Engineer of over 30yrs, the answer should be obvious but here goes.... I've recently replaced my old gas oven, which had piezo or battery ignition. The new model has electric ignition and a...

Looking to get an outdoor light installed and I've already switched out the switch to a double switch but I'm not actually certain I can just connect the new light to the switch now... Basically the other switch is connected to a two way kitchen light and the other side is not connected to...

Hi All, Due to a quick, good deal purchase I'm now the proud owner of a Wiser Kit 2. I currently have a strange set up (but all Drayton) - all controls, boiler, hot water tank etc... are in the airing cupboard upstairs. The original set up was a single Drayton hot water and C/H controller...

Hi all, bit of an ‘is this ok’ question, or could you suggest a better way....!? Want to add a socket in a hallway, but the tidiest socket to spur from already has a fused spur from it, supplying an alarm. The alarm spur is fused at 3A so not suitable for a double socket, but I don’t want to...

I'm looking to dim my kitchen downlights wholesale (integrated LEDs), but keep the control on / off, i.e. not have a dimmer switch on the wall. Is there a product out there which will do this? I've had a look but I might be searching for the wrong terminology. I've checked and the downlights...

Hi all, We recently bought a used domyos treadmill. It has a foreign plug and came with an adapter. We’ve used it prob 5 times fine but now it isn’t working there’s no power. I looked closer at the adapter and it says shavers only and has a 5amp fuse. I tried to swap it but it’s really thin...

Hi, I'm having a log cabin built at the bottom of my garden. It was originally intended to be for dual use as a summer house and for extra storage but I'm now thinking that we could use it as a gym and with that in mind, it would be great to be able to have a shower and perhaps a WC/washroom as...

Im in the middle of replacing a batten light in my shed and need some advice on how to wire it up correctly as the connections are different to the old batten light, and i've forgot which wires came out of where :( Please see attached diagram for a better understanding.

Hi All. Does anybody know anything about towbar wiring? Owing to the recent writing-off of Mrs. Avocet's Nissan X-Trail, we no longer have a tow car in the family, so I'm about to try and stick on on my beloved Alfa 164. This is a 1989 ca, so "CAN" isn't really a problem, but it does have a...

Regards: Elliott.

Hi. I'm adding an extra 170mm of insulation to my loft but I have electrical wiring running around. It's basic wiring for the lights in the bedrooms and bathroom but I wondered if they will be alright covered up? They are covered in places by 100mm (which is the reason I'm topping up as it's...