floor

Hello, I will be refurbishing a 1960s house and am considering what aspects of the plumbing might need changing, there's a couple of points in particular I would appreciate advice with. Some of the pipework looks like it might be 50 years old, other bits look like they were changed more...

Hello! I am currently renovating my house and have hit a dilemma with some flooring between the bathroom and landing. Please see the image below Bathroom floor / Hallway edge (annotated) by Samkio posted 18 Jul 2019 at 7:33 PM The image above shows the entrance to the bathroom from the...

After being let down by several structural engineers wondering if anyone on here will be able to help me. I purchased a new house 4 months ago and the garage is my next project. Water has been getting in for several years and it has rotted the existing suspended floor rendering it useless...

All, Good Morning. I am looking at converting a standalone brick and flint garage into a 2 bed holiday let. One of the questions I have is the insulation of the existing concrete floor. I was looking to install a damp proof membrane, 50mm of insulation board and then 22mm chip board floor...

Hi guys, I’m planning on sanding and re-oiling/lacquering my living room floor. It's not in a bad condition but looks like it could do with a good touch up after moving in and plastering etc. I was just looking for some advice on coating and sanding. My plan is to sand the top layer of which...

Hi, 4 days after applying stopgap 300 slc to floor long hairline cracks appeared. Is this usual. Mix was correct and cracks are not related to trowling or batches. Levels/ depth vary from 3 mm to 10 mm Any ideas or is this usual. Thanks

We recently removed a wall in our kitchen/living space. It's left a gap that we're trying to fill ourselves. I've attached an image of the floor layers next to the gap. The measurements for each layer from top to bottom are approx: 21mm, 20mm, 57mm, 12mm. I have two questions. 1) What are...

1st floor galley kitchen job (3m x 2m): I want to put click vinyl down but don't want the click to raise the finished floor level so I figure on replacing the 18mm chipboard sub with 12mm ply? Any thoughts? Do I need additional floor support perp to joists? At what ctrs? What size additional...

Are kitchen units supposed to go in 1st and then the click vinyl gets cut in around it, or does the click go down wall to wall and the units go on top?

Glued down lino is definitely not an option, hateful stuff to change. B&Q do click vinyl, but it only clicks properly along it's length, quite a few poor reviews too. Does anyone know of a good brand, maybe that uses HDF, fits together well, and won't chip if a kid drops a Tonka on it? Of a...

Hi all, picture above is of my floor in one of my rooms. As you can see it has some indentations and looks worn. I'd like to know the best approach to covering such indentations and then I'd like to try and bring the floor back to life a little on a budget. Would i use a staining product on the...

Hi All hope someone can help! We intend to screed the ground floor of our house at the weekend. With regards to the kitchen, do we screed upto and lay flooring to the kick boards or go slightly under? Also do we need any underlay for LVP click flooring? Thanks in advance!

Hi Ive search in lots of places but cant find a definitive answer to reassure me. I have some concerns about the base of the new garden room I am having built by some builders. It seems a bit cowboyish to me. The new room sits where the old shed and patio is. So the wooden base half sits on a...

Hi, I want to fix up this old shed.. I think the side has had leaves pile up from the trees, the bottom tongue and groove panel is totally rotten. The one above probably needs replacing too. They sell some the right size at B&Q? Inside the ceiling is all black - but doesn't seem rotten, but...

Hi, Hopefully I'll be at the point where I've fixed my bedroom floors and can lay the gripper rods soon.. Issue is all three bedrooms have old hearths - apparently you still need gripper rods on top. Two of the hearths have beautiful original tiles, I don't intend to do anything with them...

Hi Guys, looking to tile my new kitchen floor, however, have come across a hickup, There is a very large hole in the concrete floor from wall to wall which has collapsed slightly. I don't know why this has happened though my suspicion is that the builder who did my extension years ago knew...

Hi, I have built a small block based workshop in my garden (project here). The floor is concrete laid on hardcore / building sand / dpm. What would be a good method to finish off the floor. I was about to lay a sharp sand / cement screed coat (5:1) and then paint with a grey 2 part epoxy (I...

So far I've put down over 5mm ontop of what was required to level due to not getting a decent finish. I'm at the point of possibly hiring a floor grinder https://www.hss.com/hire/p/htc-gl270-grinder, they're not cheap & theres no guarantee it'll look good. Should I: 1. Hire the floor grinder...

Basically I wonder if anybody could give me any tips on making my loft space into a nice clean usable area. First of all I am not putting in any stairs I am still going to be using the existing loft ladder the space up in the loft is very large indeed I was hoping it would be okay to keep the...

I'm going to replace the chipboards on my landing as they are a complete mess after being taken up twice and a bodge repair by the previous owner. As you can see in the photo below, there's a piece of 22mm stuck in there when the rest seems to be 18mm around it (400mm centres on the joists...