galaxy

Greetings, Haven't been here for a while due to working abroad for a bit. My wife has been pestering me for a while now as she had to completely disable the Galaxy while I was away. This is a DIY install (unsupported) and has been working fine for many years. Recently we've been getting an...

Hi. Would like to add an additional keyprox and internal speaker. Am I ok to run the cables back to the panel like for like as the other pad just ensuring each pad and a different address on the rotary switch. As for the internal speaker it seems unclear where I wire that? Is it wired with the...

Hi all, I'm hoping somebody can help with a strange issue I have? My setup is a Galaxy Flex 50 v3.37 with multiple wireless and wired zones. Everything works as you'd expect except at times when I try part-set or full-set the alarm on the mk8 keypad, I get "check zone - final" and I need to...

I was replacing two smoke alarms to something more modern, not realizing that they were part of the Galaxy alarm setup. When I cut the smoke alarm wires the Galaxy keypad went dead. I've checked the three fuses in the Galaxy enclosure and they look okay to me. The logic board is powered...

Hi all, I've registered to see if someone can help me fault find this issue. This is on an existing Galaxy Dimension system that has been running fine for over a year. GD-520 with E080-2. I can update this post later with firmware versions etc. Immediately after unsetting, a comms line fail 4...

Hi all - Anyone know if there's any difference between the Honeywell RF remote fobs tcc800m (marketing info for which says it's compatible with galaxy G2 panel with RF portal) and tcc800ms, for which I keep coming across marketing info that says 'only works with evohome security hub'. They...

Hi guys, I need some help as I have a now out of contract ADT alarm that I cannot use as I have no idea what my user code is to login. It had tripped and needed a managers code and I couldn’t shift it as I couldn’t remember my code. I have managed to login as an engineer but is there any way to...

Hello On a Galaxy G2-20 under option 57 you can print system programming and diagnostic information to a serial printer from the program header. The installation guide states that you need a printer lead (part number A225) to do this. I have a few questions that I hope someone can help with...

Hi, i Installed a new Galaxy Flex 20 with mk8 keypad and a couple of RF zones. Had some previous issue with the tampers and low battery in a few PIRs but that has been sorted now. I have a new 7.2Ah battery fully charged. Problem is when I set the alarm I get this "ALERT-BATT LOW", ent=CONTINUE...

Hi all - On a galaxy G2-20 I'm using an RF portal c079-2 , it's a model that uses tracks on the PCB for the antennae, and has a jumper with the 'russian' frequency option. There are 2 antennae, one vertical and one horizontal - and a jumper to select 'ant1' or 'ant1 & 2'. The jumper was...

It seems that Honeywell has recently pulled the GX Remote Control Android mobile application from Google Play, interestingly the iTunes store version remains online. Does anyone have any information or knowledge of why the Android version has been removed?

Hi All, Does anybody have any experience with wiring up key switch zones on a Honeywell galaxy system? I seem to be stuck with getting this to work. Instead of an actual key switch, I want to use a relay to allow remote setting/un-setting. Looking at the manual, I need to change the...

Hi all. I know, it's a very old alarm. I am about to complete the sale of my house and want to change access code. The user codes are all unset, and when I set the system I can do it by just hitting the A key i.e. I don't need to enter the access code. I have the Engineer manual etc, but there's...

hi guys Working on a microtech 18 today replacing the webway, replaced the old webway with a new one as was faulty but I’ve ran into an issue, when exiting engineer mode it came up with module missing, I pressed the * key to remove it but now cannot for the life of me get the module back. What...

I've just installed a Galaxy Flex 20 with Ethernet module and additional trigger module and everything seems to be working. I've also got a direct mount RF portal to install but when I originally connected this I kept getting an error on the keypad (I think it was RF105 Tamper) My keypad was...

Hi All, I have a Galaxy Dimension 96 installed and set up which is fully operational apart from the external bell boxes. The two bell boxes are both Pyronix, Different models hence only one has the ability to disable the back light. I am able to wire them to either the main panel or to a...

Hi. Have been looking for a Honeywell Galaxy Flex 050 alarm panel for a job, butvsees that there are manufacturing issues at present and they are in short supply with V3.1 firmware. Can a V1 panel be upgraded? These it seems are still available Thanks

Hi, I am attempting to install a Honeywell Galaxy G2-20 System. Having a background in electronic engineering (a degree many years ago), I thought that I may be able to install the system myself. I have used the G2-20 with the RF Portal and several wireless detectors (3 x PIR's, 4 x door...

Hi all, I am new to this forum, so something about me: Living in UK for the last 13 years. Working as an electronics/acoustics engineer. Designed many audio related products and automatic test equipment systems. Got two patents in acoustics. Now about my problem: Recently I got two second hand...

i moved in to a house with a galaxy g2 wireless alarm system - I have all the codes. One of the wireless PIR units kept giving a battery low error every month or so. Replaced the battery and everything was fine. After replacing 10 batteries I figured it was time to replace the unit, which I...