light switch

Hi, I'm looking to replace a 2-way light switch for a 2-way delay light switch. I have replaced one already for a pneumatic time delay switch, but the second switch I bought has different wiring which I'm unsure about. Can anyone advise on how to rewire it correctly?

Puzzled.. I am trying to replace an old 2 gang 1 way switch (see below how is wired) to a new 2 gang 1 way touch light switch (2nd picture), however I'm confused by the wires. Although a total novice, Im guessing the one were there is 2 res wres attached, is power and is being looped over to...

Hi all I’d be grateful for your advice. I currently have two wall lights controlled by a double dimmer switch. It is buzzing so I want to replace it. I’d like to replace it with a single switch that controls both lights but as a result the wiring doesn’t appear to be a straight swap when I look...

Hello all, I am sure I am not first person to ask this on this forum... But can't find a post that matches my requirements I am looking to replace a double switch in a 1970s house but the wiring is a little confusing. Normally, I would replace like-for-like but the old switch doesn't have the...

Hello, I just wanted to check if my understand of the wiring is correct before I go on with the replacement of the switch. This is my current witch wiring: And this is the switch I will be replacing it with: If I got this right the wiring should look like this?: Thank you :)

The plastic switch component on my tennants bathroom light switch has come off. I went to change the switch and found a lot more wires behind than I was expecting. Bit of a novice with this sort of thing but felt confident after watching a video on YouTube. Was just expecting a one way switch...

I'm trying to replace a 2-gang 1-way light switch with a dimmer switch. I've never replaced a switch before, hoped it would be straight-forward but I can't figure out the correct terminals to use for a 2 gang switch, all diagrams just show a 1 gang switch. If someone could let me know which...

Hi, I replaced an old double light switch, one switch does my porch light, the other should do my lounge lights. It was an old switch with L1 L2 and L3. I followed these instructions when changing it : L1 . . . . COM L2 . . . . L1 L3 . . . . L2 And it doesn't work. I have posted a photo, any...

I recently changed a couple of ceiling roses for a newer ones that weren't grubby and yellow. I noticed something odd... in the fact there was only 2 cables going to them. In previous houses I have lived at, there has always been 3. 2 which form part of the ring/circuit, and one goes to the...

I have a dimmer switch that recently stopped working, so I'm hoping to replace it with a new one. This is the only switch that controls the light in question, so based on my googling I expected to see one red or brown live wire and one black or blue switched live wire going into the switch...

I hope that someone can help with a light switch problem. There is a single light switch which controls the lounge lights and it’s wired like this: C6990933-7979-4260-AEBF-C94C165FB7D8 by RogPJ posted 14 Feb 2021 at 12:40 PM Then there is a double light switch which also controls the lounge...

Just replacing the hallway light switch. When I removed the old one the two wires that aren’t connected in the photo fell out of their terminals so I don’t know where they go. They control the upstairs light. The downstairs light works fine without the other wires attached. also, I’m fitting...

Hi everyone. I'm looking to replace 2 2-way light switches (one in our hall and the other on the landing) with timer switches, so that they turn off automatically after a set period of time if they aren't manually switched off. I've seen the Elkay range of touch timers (links below) but I'm...

Hi, I’m replacing the light switch at the top of the stairs - it’s a regular set up, the landing light can be switched from upstairs or down stairs. I thought it would be simple but think I might have bought the wrong switch. The switch has one wire coming down into it (red) and two wires...

Hello I want to replace an old rotating dimmer switch with a wifi dimmer switch preferably, but if that works out too impossible or complicated, I would be happy enough to just have a normal 2 gang switch or 1 gang switch. It's in a living room beside a kitchen, the kitchen has a 2 gang...

Light switch is very flaky, and keeps coming away from the kitchen wall. Not good if you're about to try and sell a property. The 1-gang 35mm deep steel back box has its lugs broken off. Can't see how I could replace it as the gap in the tiles is too small. The left hand screw has a 40mm...

I need to replace pull cord light switch in my bathroom. So I ordered so called 1-way switch without checking what I have first. It looks like I have currently mounted 2-way switch. 1. This is what I have now: https://ibb.co/B3fkZcj The current is flowing only on two brown sockets on the right...

Just started watching the following video, where it is claimed that the plastic bit in the string of pull cord switches is for insulation purposes and thus is a safety device. I can understand this if true, although is new news to me. Any truth to this, have you heard this before, and is there...

Trying to change a broken Volex light switch with a Click Thats what it looked like when I took out the Volex switch I've mirrored how the cables went in with the click switch but lights aren't working. There all in L1 & L2's like the original Volex any help?

Hi all. have a 3 gang light switch in my hallway that controls the porch light a wall light and the downstairs and upstairs hall/ landing lights I want to combine the porch and wall light into one switch therefore making it 2 gang. Is this possible? Thanks in advance.