pyronix alarm

Customer had alarm installed a few years ago. Never any problems with the keyfobs or alarm. Last service was about 6 months ago. Customer calls today to say that all his keyfobs (i think he has 3) now wont set the alarm but they can unset the alarm... Any ideas?

Hi all, Losing my mind a little, I’ve got a pyronix enforcer alarm system and a deltabell external sounder. I have lights etc on the box however when I run a siren test from the control I’m not getting anything. On the panel my outputs are 14 strobe and 16 bell...is there something I’ve...

I have installed the alarm. The alarm sets fine when I present the fob and leave via the final exit door. but when I present the fob and go upstairs to bed the alarm sounder goes off. I have no pir’s upstairs Front door set as type 7 Back doors set as type 8 Pir’s are set as type 9 I think...

Hi Ive had a pyronix enforcer alarm for a fair while now with no issues. Its all set up to my phone too. Just changed from plus net to bt fibre with a new SSID and pwd. Tried setting up by the "WiFi device" method but the virtual wifi channel never actually connects. Do I try the though...

Hi all, New here and Looking for some help if possible. i have a current (but dated) working alarm with 4 wired pirs, wired bell and wired door contact but need 2 new pirs that can’t get wires to. All wiring working and in very good condition. Having a pyronix enforcer fitted (want an app based...

I have got an issue with the siren outside the house, which has started triggering a "tamper" alert which is quite deafening. Currently waiting for the electrician to look into that, but in the meantime trying to reduce or stop it altogether. Been into engineer mode, but am unable to find the...

Hi all Can someone advise me whether I should update the app on my iPhone to use the new Pyronix ProControl+ app or should I stick with HomeControl+? The splash screen on HomeControl+ states that it has been replaced by ProControl+ but seems to continue to work fine for me. Anyone else...

The other day for the first time in 4 years, my Pyronix Enforcer Home Control+ panel started beeping and went into a fault condition for the first time under a normal idle state. The error what I believe caused the "fault condition" was a "SMS call Fail" event, although not sure why it...

Exploring my Enforcer I came across the Key Pad Menu.. The menu goes like this: Language Zone Status Keyclick Vol Master Vol Tag ID Factory Reset(----) Backlight Force PA/Fire Timer Address (00) I was trying to factory reset the system so I could set this up from scratch. I entered the...

Hi Again, So the story to date. Ive installed the system over the last couple of weeks. Installed the panel programmed the system connected all the sensors to the system and then put them back in their boxes until today. So today I started to install the sensors. I bought the ceiling brackets...

I've installed the above alarm and everything seems to work how I would expect it to. I have also installed Pyronix Enforcer secure wireless keypad which I can arm/disarm with the keypad but I cannot use the Proximity tags. I can use the prox tags on the mail panel. Is their a config required...

Hi folks, I have a friend with an Pyronix Euro 46 panel connected to Pyronix cloud through a small alarm company. He wants to take control of the panel himself but the company refuse to release the system from their cloud account as he is under contract. I have a fair amount of experience...

Hi, I have a wired in Siren to my Pyronix Enforcer. When I tested the bell it activated the LEDs and I heard a faint chirrup of the siren going. Any ideas of how I can fix this. Is it a new bell unit or is this a know issue easily rectified? Thanks for any help and advice you can give...

Hi, Less than a year ago I installed a pyronix enforcer into my house, with a few sensors and a wireless siren externally. Recently, the alarm has been randomly sounding internally with an alert to say that "Wrls Poll Fail - Siren 1". The siren hasn't sounded for any long periods of time...

Hi All, I've fitted a few of the pyronix enforcer wireless alarms and they are a great unit, clients always love the mobile platform access. But on this occasion I'm struggling to get the unit connected to my network, I've been through the usual settings in communications and activated the...

Hi folks, The house I've lived in for a year has a Pyronix Enforcer 10 and during the last week it has sounded when unset at random times. Last Thursday it went off twice in the evening, showing a tamper with areas A, B and C all affected. After a quiet weekend, it has gone off 6 times in the...

I see a lot of people with experience of these panels. I have just installed the panel and am trying to connect to my wifi network. Neither of the two methods noted are working for me. I have tried entering the SSID and password manually. I also used the other method that uses a smartphone. The...

Can anyone help with the procedure to replace battery in a KX12DQ-WE detector. not a lot of help from manual, and even less help from customer service whose view is pay an installer to do it