pyronix enforcer

I see a lot of people with experience of these panels. I have just installed the panel and am trying to connect to my wifi network. Neither of the two methods noted are working for me. I have tried entering the SSID and password manually. I also used the other method that uses a smartphone. The...

Hi all. I’m looking for some help installing a door sensor for a Pyronix Enforcer and would be grateful for any advice. I set up this system about 4 years ago and have not had any issues. Now I’ve tried installing a door contact and when ever the door is opened, the siren sounds. This...

I have recently had a Pyronix Enforcer alarm installed and have 2 remote keypads, one wired and one wireless. I can change the volume of the wired keypad easily enough by going into the keypad menu, but the wireless keypad has no LCD display, so presumably does not have the same settings...

I have my Pyronix Enforcer set up with A (away / all sensors enabled) and B ( home / door & window contacts only) zones. Is it possible to display the armed status of the panel, either on the LCD display or by illuminating the A or B buttons depending on which zone is set. We set zone B...

The manual for the MC1/Shock/WE shows the shock calibration jumper in the middle of the sensor but the physical sensor has not jumpers at this location. The physical sensor has 3 pairs of jumpers in total but none in the middle of the sensor as per the manual. Two pairs of jumpers are at no.1 in...

The Pyronix Enforcer Kit comes with the DIGI-WIFI communicator. I have connected the Enforcer to my WIFI and verified the signal (14) Manager menu does not have "Set Up App Data" option as per manual 14.8. The manual has a note that this option is only visible with a Homecontrol+ compatible...

I have just completed programming my Pyronix Enforcer v10 5 x magnet contact/shock sensors set on downstairs windows & patio doors - A & B 2 x PIR's - upstairs and downstairs hall A only 1 x door contact on front door A & B All programmed and working except for exit. If...

hi I’m new to the forum and new to owning a house with this system. :) Previous owner has not got the engineer code and I can’t do much with it. No previous company on the panel name just says enforcer. Does anyone know how to reset the panel or is it a case of buying a new one? It’s an...

Hi, I have a Pyronix Enforcer system. My KF4-WE key fob is on the blink. Sometimes when I press any button I get a single amber flash. Sometimes the red and green LEDs flash alternately for over a minute. The battery is fine (I have tested it and also swopped it into a second fob). I have...

Hi, I have a Pyronix MC1/SHOCK-WE sensory and the shock circuit is constantly "open" so it can't be used or set. I have tried recalibrating the shock sensor but it is not helping. The magnetic contact switch is working perfectly it is only the shock circuit that is not working. The battery...

Before Arming a Pyronix Enforcer Panel says testing after a user code is entered before arming. What causes this or how do I stop it. It doesn't happen with a fob! Any insight will be welcome!

Pyronix Enforcer V10 - "Wireless Ch To" entry in the Panel log at almost the same time each day for the past two weeks. From research I think it is seeing some 'jamming' or interference and hopping channels. Is this understanding correct? Is something wrong with the installation? Can it...

Pyronix Enforcer V10 Panel Log has entry that says "Logs nearly full" Do you have to manually manage this? or does the panel delete old entries when its full?

Hi, i have installed the pyronix system, all works well, but the issue is with the wireless bell, during the walk test and when the alarm goes off, only the strobe light flashes but there is no siren sound? does any body have any ideas why this might be? i have looked through settings and...

Hi guys, was wandering, need some help please.. have this setup. A = Full Set, B = Night Set, C = House Parameter Input 1 / Front Door Mag / A, B, C / 07 Final Exit Input 2 / Kitchen Window Mag / A, B, C / 06 Intruder Input 3 / Kitchen PIR / A, B / 06 Intruder Input 4 / Utility Door Mag 1 /...

I will be replacing an old grade1 DIY wireless system in my 3bed semi with something more reliable, and importantly, something I can control with my phone remotely. After much research, I think Pyronix Enforcer V10 with HomeControl+ seems to be the best grade2 wireless system for remote control...

Pyronix Enforcer installed. Downstairs sensors and contacts level AB One landing PIR level A. Enforcer panel is in cupboard upstairs somewhere so using a wireless arming station keypad in the hall. The front door contact final exit. The hall PIR next to it 09 An adjacent room PIR also 09 as it...

Hi guys, I was wondering if someone could help me, I have a Pyronix Enforcer V10, and I would like to connect TWO internal Pyronix Sounders to the system but I am unsure how to connect to the internal IO board, or if to connect any resistors? I do not currecly have any other item connected to...

Hi All, I am considering updating my old Alarm system and had a few questions I was hoping some of you guys might be able to help with. My current alarm system is a wired system with PIRs, bell and front door contact. It has a main panel and a wired keypad. 1) In upgrading it, I was hoping I...

Just a few questions about the Pyronix Wireless Enforcer system, as I am installing one tomorrow at my grandparents. 1) What is it about a 4 digit code not being compliant with BS8243 for unsetting the system as stated on the panels flip down guide? I take it it has nothing to do with the...