texecom alarm

Hi there, I’m after some help regarding my alarm. Currently, my sounders and strobe do not work when activated via the programming route (the engineer code followed by 05 - page 19 on the manual). When I plug in the battery and power, I can hear the external sounder go off but the strobe does...

After opening up my Elite 24 for the first time over the weekend, it was suggested that it be useful to check whether it's got some sort of communicator for monitoring. I enclose pictures of the main panel but not sure what I'm looking for. Many thanks

I've been in a new place with a Texecom for about 3 months and this morning (why is it always weekends?) the control panel has started alarming with a "call engineer" message and I can't work out how to turn it off. Manual is for "Premier 412/816/832". Code supplied by previous owners not...

As seen in the picture below there is a red fault light on and the rest of the system configured on network 1 has no power. The orange thing furthest to the left (pardon my lack of understanding) is running extremely hot Help appreciated.

Hi, I have a texecom elite alarm - working fine, I get notifications via the connect app however when i try and log in, the app keeps crashing. I am using an android phone - it used to work fine previously. any help would be appreciated.

I’ve recently installed a premier elite 24 system and upon entry to the property there is no entry tone and the alarm won’t sound. I get an exit tone, and when entering it says Area A arm etc but there is no sound on entry. I have no door contacts and have the PIR on the entry hallway as...

I have recently aqquired a Texecom Premier Elite alarm system for my house and I have installed it myself and so far its been ok as someone who has done lots of research, carefully read manuals and has an interest in alarms (please note this is a self install/DIY system) I also have a Texecom...

Hello I was wondering how to link out a zone on a Texecom Veritas R8 i was wondering also what could I use to link the zone out Many thanks Thomas

I’ve a Veritas R8 panel with the unset light flashing. Not a duplicate thread as: I checked battery output as was dead Checked fuse … ok Replaced battery … fault persists Closed panel and enter code + reset 2x … fault persists I’m now not convinced the panel is recharging the battery when...

Hi everyone. I have had a Veritas Excel for around 8 months now. Ever since installation it has been nothing but trouble. It's not the installers fault, just the system. Alot of the time to begin with in the evenings it would trip randomly and on the event log would state RKP OFFLINE and a...

I have a Texecom Premier Elite and SmartCom alarm system. I keep getting issues with access via the app failing, and the alarm installers haven't been super helpful, so I thought I'd see if I could get some clues here. The SmartCom (CEL-0001, Hardware Revision 26 if that helps) is connected to...

Hi sorry for a longer post, just trying to give as much detail as possible. I have recently moved into a house with a Texecom Elite 48 alarm ('menu - 4' shows sw v5.01.02.LS1) with a smartcom module installed. Over the past week or so I have been investigating the configuration of the alarm...

Hi all, I’ve just installed a texecom 64W Live, (main panel is in the garage) and wireless keypads have been fitted in the main house and out house. I’m struggling with the signal from the outhouse which is about approx 15-20meters from the main house. Is there any specific signalling booster or...

Hi Been pulling my hairs out over this. Got a new self install system (elite 64w with smartcom, 1 wired keypad and 1 wireless keypad) and everything is almost working perfectly, exepct for one thing - I cannot disarm from either keypad (wired or wireless). I am however able to disarm by keying...

Hello, Quick question for my texecom premier elite. I'm sure people will know the answer straight away. After getting the batteries replaced my part arm doesn't seem to be working as it did before. The back door works fine, when part arm is on and the back door is opened the alarms sounds...

My wifi provider was changed, so I am trying to connect my Smartcom to the new Wifi Connection so that I can reconnect my app. However, I am getting a “no internet connection” message (as seen on the screenshot below) when I’m trying to connect to Smartcom. I am unable to connect to the...

Hi There, I have a Texecom panel currently used for my home alarm. Everything is working great except that I wired up my electric fence energizer as an additional zone. Basically connected the energizer positive and negative to a normally closed 12v relay board and wired the zone as follows...

Hello All, Have been a lurker on this forum since I bought the premier elite alarm panel and have had some useful insights along with the texecom manuals. I have managed to setup all the zones and areas on the alarm and have successfully fitted the sensors , panel (5.04.02 Version) and a smart...

I have suddenly started getting a tamper issue with my Premier Elite Micro Shock Wireless sensor. I have checked the device and the cover is on fine however it will randomly trigger the sensor alarm. Does anyone know why this might be? Resetting the tamper fault will fix it for a couple of...

Hello, I have a Texecom Elite 64W with a Smartcom, I have internal sounders connected to the panel outputs. When the alarm is triggered and I attempt to disarm from the Connect App the external bell will stop but the internal sounders do not. The app says the system is "Disarmed" but the panel...