I have both types. Can’t get on with the hand pumped one and prefer the basic one. To get the filter out, pull the filter up a little, grip it with a pair of pliers and twist and pull. Be brutal. 
Scudo (Expert/Dispatch) Rear Shoe Auto Adjuster Questions?
- Thread starter ReganAndCarter
- Start date
Sponsored Links
I have both types. Can’t get on with the hand pumped one and prefer the basic one. To get the filter out, pull the filter up a little, grip it with a pair of pliers and twist and pull. Be brutal.
In that case I will need a late Xmas present of a pair of thin, bent nose pliers. The resevoir is under the scuttle overhang, so not a lot of room to work above it.
Mum's cracked and leaking cistern - replaced. Van's leaking rear brakes - replaced.
Just noticed occasional small drips of diesel on ground and smell of diesel from van. Will no doubt be back for more advice.
Just noticed occasional small drips of diesel on ground and smell of diesel from van. Will no doubt be back for more advice.
Looks like the fuel filter housing is leaking - more of a weep than a regular drip. Seems to be from the rubber seal where the top is held down by a screw on ring. Not sure if these types of plastic housings on HDI Citroen, Peugeot, Fiat, etc engines are usually problematic. When filter has been replaced in past, has taken several attempts to stop the rubber seal leaking - worse than it is now.
Few years ago a garage changed the filter while it was in for other work. Straight after when I was driving it, it was leaking quite a bit. Took it back and mechanic thought he had stopped it. Had to go back a second time - mechanic emptied his bin out on the floor, found the old seal which he reinstalled and leak stopped. Each time the the filter has been changed since, the original seal has been reused without any problems.
Anyway, I have just ordered the proper tool (photo below). When it arrives, I will see if the securing ring needs a slight tighten. If this doesn't cure it, I will get a genuine filter with new seal and put that in.
Few years ago a garage changed the filter while it was in for other work. Straight after when I was driving it, it was leaking quite a bit. Took it back and mechanic thought he had stopped it. Had to go back a second time - mechanic emptied his bin out on the floor, found the old seal which he reinstalled and leak stopped. Each time the the filter has been changed since, the original seal has been reused without any problems.
Anyway, I have just ordered the proper tool (photo below). When it arrives, I will see if the securing ring needs a slight tighten. If this doesn't cure it, I will get a genuine filter with new seal and put that in.
108mm Fuel Filter Wrench Removal FITS Renault CITROEN + PEUGEOT HDi 3/8'' Tool | eBay
Especially designed for use on fuel filters fitted to Citroën, Peugeot and Renault models fitted with HDi engines. Suitable for Citroën, Peugeot and Renault models fitted with HDi engines. Specialist tools for most parts of the modern motor car are now required to attempt even the simplest of tasks.
www.ebay.co.uk
Links in this post may contain affiliate links for which DIYnot may be compensated.
Sponsored Links
- Joined
- 25 Jul 2022
- Messages
- 13,424
- Reaction score
- 1,059
- Country
Absolute nightmares to get to seal .
The tool should help but look around for new filter with housing complete ? Much easier and not usually badly priced.
Can't remember the site but try ' Alfa and fiat spares' online ?
Alfafiatparts.co.uk. nothing to do with me but often useful for filters and housings complete
The tool should help but look around for new filter with housing complete ? Much easier and not usually badly priced.
Can't remember the site but try ' Alfa and fiat spares' online ?
Alfafiatparts.co.uk. nothing to do with me but often useful for filters and housings complete
Thanks, that confirms what I thought. Not a very good design. Do you usually find that cutting your losses and buying a new one solves the problem?
Genuine ones not too expensive on Ebay.
Genuine ones not too expensive on Ebay.
Genuine Fiat Diesel Fuel Filter Housing 9643496480 Peugeot Citroen | eBay
Genuine Fiat diesel fuel filter housing which is still in its sealed unopened packaging. New Old Stock. The box is grubby and damaged from storage. Fiat part number is 9643496480. Will also for Peugeot and Citroen models part numbers 9642105180 and 9638780280. Fiat Scudo and Ulysse...
www.ebay.co.uk
Links in this post may contain affiliate links for which DIYnot may be compensated.
- Joined
- 25 Jul 2022
- Messages
- 13,424
- Reaction score
- 1,059
- Country
Yes. Easier, quicker and usually only a little difference in price.
Genuine ones not too expensive on Ebay.
Genuine Fiat Diesel Fuel Filter Housing 9643496480 Peugeot Citroen | eBay
Genuine Fiat diesel fuel filter housing which is still in its sealed unopened packaging. New Old Stock. The box is grubby and damaged from storage. Fiat part number is 9643496480. Will also for Peugeot and Citroen models part numbers 9642105180 and 9638780280. Fiat Scudo and Ulysse...www.ebay.co.uk
Links in this post may contain affiliate links for which DIYnot may be compensated.
A good smear of grease on the rubber seal often sorts it, newer ones have Torx screws I think.
John
John
- Joined
- 25 Jul 2022
- Messages
- 13,424
- Reaction score
- 1,059
- Country
Ive never usually been that lucky. The cases often seem to be just so slightly out of round after a few filter changes.
I never even fight them nowadays. A complete unit change or not at all.
Just wanted to check what makes the rear drums' adjusters turn to make the shoes move outwards to the correct gap from drum. Unless I have it wrong, some work by pressing the brake when going either forwards or in reverse - others when the handbrake is operated.
Looking at the picture below of the setup I have, the adjuster seems to be located one end in the shoe and also the handbrake lever. Because it is located in the handbrake lever, does this mean that operating the handbrake makes the adjuster work? Or does pushing on the footbrake make the adjuster work?
Looking at the picture below of the setup I have, the adjuster seems to be located one end in the shoe and also the handbrake lever. Because it is located in the handbrake lever, does this mean that operating the handbrake makes the adjuster work? Or does pushing on the footbrake make the adjuster work?
Last edited:
Supposedly, each time you engage your handbrake, if there’s enough movement, the lever should move the adjusting wheel. Rarely happens though.
- Joined
- 25 Jul 2022
- Messages
- 13,424
- Reaction score
- 1,059
- Country
Every time you use the footbrake it stretches the adjuster bar out and allows it to click round if it's ready too.
The adjustment is NOT done by the handbrake. Using the handbrake without the adjuster spread out will just give you a long brake pedal and a long, ineffective handbrake travel
The adjustment is NOT done by the handbrake. Using the handbrake without the adjuster spread out will just give you a long brake pedal and a long, ineffective handbrake travel
Sponsored Links
