|
Trend Router Guide Bush 11mm
Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. Specifications: ... |
£13.95 More Information |
|
Trend Snappy Flat Bit 22mm 150mm
An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Specifications: • Shank Diameter: 1/4 hex • Dia Metric: 22 • Overall Length Metric: 152... |
£7.49 More Information |
|
Trend STC Spiral Downcut Left Hand Router Cutter 8mm 25mm 8mm
Trend 8mm diameter down cut spiral cutter - 8mm shank, 25mm cut length. Spiral downcutting configuration offers the cleanest finish on the top surface of the workpiece when used in hand held or overhead CNC routing applications. Two flute desig... |
£46.95 More Information |
|
Trend Chamfer V Groove Router Cutter 12.7mm 6.5mm 1/2"
Use for bevelling, chamfering and for producing mortar grooves. Approximately 1.0mm flat will be found on the nose. Specifications: • Shank Diameter: 1/2 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric... |
£31.95 More Information |
|
Trend Replacement Cutter Bearings Metric OD 14mm
Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Alw... |
£16.95 More Information |
|
Trend CRAFTPRO Two Flute Straight Router Cutter 7.9mm 25.4mm 8mm
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Specifications: • Shank Diameter:... |
£16.95 More Information |
|
Trend Bearing Guided Bevel Trimmer Router Cutter 15.9mm 6.3mm 1/4"
Gives a smooth bevel finish for laminates and other materials. Bearing follows the board beneath. Specifications: • Shank Diameter: 1/4 • Dia Metric: 15.9 • Dia Imperial: 5/8 • Cut Length Metric: 6.3 • Cut Leng... |
£29.95 More Information |
|
Trend Professional Two Flute Straight Router Cutter 17mm 25mm 1/4"
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. Has a TCT plunge centre tip. Specifications: • Shank Diameter: 1/4 • Dia Metric: 17 &... |
£49.95 More Information |
|
Trend Flat Ovolo Router Cutter 25mm 8mm 1/4"
Panel mould and edge mould cutter. Specifications: • Shank Diameter: 1/4 • Dia Metric: 25 • Cut Length Metric: 8 • Overall Length Metric: 36.6 • Radius 1 Metric: 12... |
£56.95 More Information |
|
Trend CRAFTPRO Wood Cutting Mitre Saw Blade 250mm 42T 30mm
Trend Craft Pro saw blade - 250mm diameter 30mm bore 42tooth TCT Specialist blade with -5 degree hook, 3mm kerf with 2mm plate thickness for clean, safe cutting with mitre saws. Ideal for fast and safe general purpose crosscutting of heavier ti... |
£38.95 More Information |