|
Trend Bevel Bearing Guided Router Cutter 30mm 35mm 1/2"
Useful for bevelling thick timbers. Certain sizes can be used for jointing, boxes, pilasters and carcassing. For full bevels, template should be fitted to component. Specifications: • Shank Diameter: 1/2 • Dia Metric: 30... |
£98.95 More Information |
|
Trend STC Spiral Downcut Left Hand Router Cutter 3.96mm 16mm 1/4"
Down-cut spirals are ideal for routing small workpieces or for holding workpieces secure in vacuum jigs. Down-cut pushes woodchips below the work. Two flute. Specifications: • Dia Metric: 3.96 • Dia Imperial: 5/32 &bul... |
£40.95 More Information |
|
Trend STC Abs/Pvc Two Flute Router Cutter 6.3mm 25mm 1/4"
Used to slot and trim low melting point plastics such as ABS, Styrene and PVC. For maximum life these cutters are Solid Carbide. Two flute for fine finish. Specifications: • Shank Diameter: 1/4 • Dia Metric: 6.3 • ... |
£39.95 More Information |
|
Trend CRAFTPRO Ogee Panel Router Cutter 19.1mm 11.1mm 1/4"
Small panelling cutters, popular for decorative cupboard doors and furniture embellishments. Specifications: • Shank Diameter: 1/4 • Dia Metric: 19.1 • Dia Imperial: 3/4 • Cut Length Metric: 11.1 • Cut Length I... |
£44.95 More Information |
|
Trend Bearing Guided Thumb and Hand Mould Router Cutter 69.2mm 16mm 1/2"
A quarter ellipse cutter for architraves and hand rails. Can be used to form the top portion of handrail moulding when used in conjunction with Ref. 93/3. Specifications: • Shank Diameter: 1/2 • Dia Metric: 69.2 • Cut... |
£131.95 More Information |
|
Trend Radius Router Cutter 18mm 19mm 1/4"
For coves and part of a rule joint. Specifications: • Shank Diameter: 1/4 • Dia Metric: 18 • Cut Length Metric: 19 • Overall Length Metric: 48 • Radius 1 Metric: 9... |
£67.95 More Information |
|
Trend Bearing Guided Ovolo and Round Router Cutter 28mm 12.7mm 1/4"
Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for s... |
£68.95 More Information |
|
Trend CRAFTPRO Round Over and Ovolo Router Cutter 25.4mm 12.7mm 1/2"
Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also... |
£44.95 More Information |
|
Trend Two Flute PTFE Coated Non Stick Router Cutter 15.9mm 19mm 1/4"
Gives a clean finish to abrasive materials such as chipboard, MDF, plywood and certain hardwoods. For housing, grooving and mortising. Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long lif... |
£31.95 More Information |
|
Trend Replacement Cutter Bearings Metric OD 22mm
Bearings are shielded to prevent penetration of dust and grease packed for life. They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure. Scrape off any resin build-up. Alw... |
£15.95 More Information |