hive 2 wiring advice

Help! I'm trying to install Hive active heating 2 to replace my existing system but I'm not too sure on the wiring, I've found tons of guides and posts about this already but I'm not able to transfer the solutions to my setup. This damn wiring is starting to infiltrate my dreams so any help or...

Hi, looking for advice on switching over as per the title. I've read over a few of the other posts on here but can't see wiring like how my Honeywell thermostat. There's too brown going to live, they would just go in Live on the Hive? Two blue going to neutral, same on to neutral on the Hive...

Hi sorry i’m new here but saw some Great advice. I have a new Hive system but I'm struggling to install, trying to replace an RWB7 (pic 1 and 2) with my Hive controller which is located on first floor but also have an SCR wireless receiver (pic 3 and 4) in garage (floor below) and an RF3 (pic5)...

Good evening, I'm planning to replace my hortsmann centaurplus C11 with a hive thermostat. It seems like a simple swap, but I just wanted to check that I wasn't completely misunderstanding the wiring. Below is a picture of my current wiring and the wiring diagram for the programmer. It is...

Hey, Looking for some advice with fitting hive, replacing my Danfoss FP7898/FP715. I’ve pulled the programmer off and looked at the wiring and each connector has cables in apart from ports 1 and 2. I have a boiler with separate water tank so require the 2 channel hive. I’ve attached the photo...

Hi All, I'm planning to replace my existing Potterton EP2000 with a dual channel Hive receiver/ thermostat. Currently we have no thermostat and all the rads have TRVs, so will primarily be using the Hive as a better scheduling capability with remote access. Existing wiring doesn't look too bad...

Hi, I have today wired up the Hive thermostat, receiver and hub. Connected up the wires how they were on the old receiver and now the boiler is not working. Works from the main thermostat to receiver, but doesn’t action the boiler. Have now taken off the plate on the boiler and can see...

Trying to replace our Scottish Power Climote CH/HW controller with a Hive unit. I can perform some basic electrical tasks but this is possibly beyond me? ...I'm after some advice as to whether this is possible as a DIY task or if I need to call someone in. Basically there are many more wires...

Hi all Desperate to replace the pretty rubbish Geo Cosy system that we got for free a few years ago when we switched our electric supplier with a nice new Hive system. I’m in a better place than most for this as we had a Worcester wireless thermostat originally and the engineer had to...

can anyone help with wiring my hive heating system the wires same to be different on the old controller.

Hi, I am looking for some advice regarding wiring a HIVE with a thermostat. I believe that I have wired the HIVE receiver correctly, but it is not powering up? Old thermostat wiring: IMG_6529 by Anton Kaszubowski posted 10 Aug 2020 at 11:12 AM HIVE wiring: IMG_6530 by Anton Kaszubowski...

Hi All, I have been given a Hive 2 With Dual Channel Receiver. I would like to use it with my Worcester Bosch Greenstar Heatslave ii 18/25 After reading around online I am aware that the single receiver version should be used for Combi boilers. However it can also be seen a Dual Channel...

Hi Having trawled every post and site I can, I’ve reached a point where I sheepishly need to raise my hand and admit defeat. Help? I’ve installed hive following all the guides I can and have had successfully installed the unit and it responds to the thermostat with both the power light being...

Looking for some help fella’s installing a single channel receiver into a systems that has a emt2 and a wired thermostat. I have tried everything...... as it’s all taken off I only have a diagram of how it was originally wired. All in twin and earth btw the 240v spur went to the L,N of the...

I'm trying to install Hive active heating. I have a Glow worm Easicom 28 combi-boiler which is currently connected to a Salus ERT20RF receiver. I was hoping that somebody might be able to confirm whether the wiring I plan on doing is correct. I'm basing this on this thread...

Looking for some help / guidance to replace our existing Honeywell cm921 thermostat with a Hive. I've removed the faceplate and there is a red wire connected to A a yellow wire connected to B and a blue wire going to one end of a terminal. I can also see a green/yellow wire behind this not...

Hi, I have a combi boiler (Potterton Promax HE Plus) and a Myson volt free switch thermostat (powered by 3 aaa batteries). I want to replace the Myson with Hive receiver. The Myson has two wires Brown (which I think is Common) and Black (which I think is Heating On). See picture. I want to...

I’ve recently bought Hive and want to have ago at installing it myself. I have a basic understanding of wiring and once I can figure out what does what on my old programmer I'm sure it’ll be fairly straight forward. Can someone explain to me what (if possible) these wires are doing...

Hello, I live in the UK and my home has a oil fired boiler which is gravity fed. I bought a hive dual channel receiver as my home has a separate hot water tank. It turns out that the switching for the hot water is within the boiler outhouse so I will only be able to set up for a single channel...

Hi, I have moved to a house with a oil Combi boiler and a thermostat (Grant) which is on the wall in the kitchen. Can I replace this with my hive receiver do you know? I'm a joiner to trade so very limited ability with things like this although I replaced my old one but it was like for like...