hive 2 wiring advice

Hi all Installing a hive in replacement of our antique Honeywell St699. Just wanted to check regarding the wiring of the thermostat to bridge it. Am I right in thinking yellow wire needs to join blue to complete the circuit? IMG_20191003_140921 by Thematrix12 posted 3 Oct 2019 at 2:45...

Looking for some advice? Installing a Hive Multizone in a property. It has the Danfoss programmer. See attached wiring for it; Would I wire this like for like as per the Hives instructions and just remove and cap the remote sensor. See attached photo? Then would I get the single channel receiver...

Hello back in December I fitted a hive with my ICOS HE12 boiler. It seemed to be working well until the weather improved and I turned the heating off. At this point when the hot water fired up the radiators got warm yet the hot water didn't. I tried swapping the CH off and HW off wires which...

Have just purchased a dual channel Hive and would appreciate if someone could confirm my wiring proposal attached. The solid lines represent current wiring using Honeywell timer and stat, the dotted lines represent proposed wiring to Hive. (British gas arrived and then refused to install as we...

Hello, would be glad of some (simple, I think) help. I believe we have an S Plan system with 2 valves - one HW and one CH. Currently the thermostat is separate with a 3 core plus earth wire and the Lifesytle timer backplate looks like the attached picture - i.e. only the HW and CH 'on' wires...

Hi, I know this has been done to death but I was unable to find something relevant to my boiler. I have a hive hearing single channel receiver and I would like to check my wiring is correct. I have posted pictures of what is present already. I have wired a 3 wired cable Live to live...

Hi I’m looking at fitting a hive control in the place of a potterton EP2 I understand the live and neutral but can’t seem to get the wiring for the on/off for both the heating and water I have attached a photo of the current wiring Could someone please assist as to what order I should wire I...

Thanks in advance for any help I'm installing hive as per instructions on an older thread. The stat had two wires connected, and a third I'm assuming is neutral that wasn't connected. Connected the hive backplate including the li k between live and the first pin, but reciever doesnt come on when...

Hi I've bought a Hive receiver & theromostat with dual HW & CH controls to replace the existing Drayton HW & CH timer control and wired thermostat. I tried to set it all up last weekend and everything was going well until I tried to replace the thermostat. I set up the hive hub, changed the...

Hi Can anyone help me with how to wire a hive dual channel receiver to a Baxi Platinum? I know it should be a single channel receiver but is it still possible!? See attached wiring diagram for the boiler and hive Thanks

i have Valiant Ecotech pro 24 ( 2011 ) model boiler and Hive dual receiver i wired up however heating wont switch off i assume its because of wiring and its not controlling boiler. my old relay box to wireless thermostat was wired up like picture attached. the Hive Reciever is wired up with...

Hi New to this so please bare with me. Please can anyone verify the wiring of a Hive single channel reciever into a Worcester 28cdi combo boiler. I have attached a diagram of the hive connections and also the wiring for the boiler connections. Some say leave terminal 4 on the hive empty others...

Hi, I have an oil fed Geminox FCX 30c boiler (https://www.manualslib.com/products/Geminox-Fcx-30-C-4112227.html) which has REG 103 (FBR1) ambient thermostat connected to it (as well as an external probe thermometer) The boiler has a mains power cable that plugs into socket in boiler room and...

I have just bought hive single zone kit including hub. I have underfloor water heating in one zone, which I intend to control via hive thermostat. This would have its own two port valve. The second zone is upstairs with radiators, with a dedicated 2 port valve. I plan to control this via a...

Another hive thread! Hi all wanting to replace my current digital timer/thermostat with a hive V2. I have a Worcester Bosch Green Star 30si Combi boiler. My current setup is as shown in the attached image. The thermostat is in my landing and boiler is in the garage. The boiler connects to a...

Trying to replace Horstman 425 Diaem with a Hive. Problem with the old controller both HW and CH had to be in the on position for CH to work. There were 2 wires in the first on position and 1 wire in the second on position on the backplate. Rest were common positions and jumped across. Back of...

hi guys..just picked up a hive active heating thermostat (for combi boilers). I currently have a horstmann 425 coronet with a downstairs wall mounted thermostat and a vaillant ecotec plus combi boiler. As it is a combi boiler ,i thought to wire the hive thermostat it would just be L N E and CH...

good morning. I’m after so information on wiring my Hives up. I’ve just bout the active heating and extra hive We have 2 thermostats to replace. In my current thermostat they only have 4 wire. L, N, E and a L when the heating is called (CH on?) I’ve put the wires to the corresponding pins...

I am currently looking at installing a HIVE Active heating control unit to replace a Danfoss TP5. I currently have a 3 core and earth cable running to the existing heating controls (battery powered unit) I have attached my existing wiring diagram and the HIVE wiring diagram. Please also see...

Hi All, I setup Hive 2 a while back for downstairs heating and hot water and it works perfectly. This meant that my upstairs rads were still controlled by a danfoss tp5000 programmable room thermostat in the bedroom. Ive been out and bought the multizone kit for hive with the plan to replace...