hive

Evening all I have the Hive thermostat on order and should be here tomorrow. I currently have a Salus RT300RF wireless thermostat which i will be replacing. The boiler is a viessmann vitopend 100 combi The current wiring on the Salus receiver is:- COM - Grey wire and brown loop NO - Black...

Idle curiosity really- has anyone ever done the sums to see how long the things take to repay their cost by reducing the heating bills/making the home more comfortable I can see the theoretical attraction but not sure about the actual. For instance, most of the year I'm at home on a normal...

Hi, Brand new worcester bosch installed two days ago with hive controller. Turns on as per schedule in the morning but then does not turn off at all unless done manually using the boiler controls. Installer says hive is working fine as is the boiler and the fix requires a new 'suppressor'...

Hello, I am trying to replace an old Honeywell T6360 dial thermostat with a Hive single channel link. I have an Alpha CB2028 gas combi boiler fitted with the optional clock timer...

Thanks in advance for any help I'm installing hive as per instructions on an older thread. The stat had two wires connected, and a third I'm assuming is neutral that wasn't connected. Connected the hive backplate including the li k between live and the first pin, but reciever doesnt come on when...

Hi I am looking at possibly upgrading our existing system with Hive, Tado or similar. Hive is my current preferred option as I have seen a good deal on an approved re-sellers website. Our current system is a two zone using TP5000 controllers. We have a Gledhill Boilermate SP and GB20 boiler...

Hi all I’ve got a receiver fitted on to a the boiler and purchased a hive 2 thermostat and hub 360. The thermostat won’t connect to the receiver even when I reset the receiver so it is flashing Amber. Called hive and they said maybe a compatibility issue with the boiler. Has anyone got a...

Just bought hive active heating and hot water pack. Currently have what I believe is gravity system ‘Y’ type. Boiler, hot water tank, 3 way valve, room stat, tank stat and programmer. Instructions state ‘dual channel required for boilers with hot water tank’. Dual channel wiring diagram in...

Hi all, I'm after some assistance in wiring up my new Hive Active Heating Thermostat (with single channel receiver). My current setup consists of an old heating timer, connected to my Worcester 24i Junior combi boiler. I don't currently have a thermostat. I've tried to draw a wiring diagram...

Hi I've bought a Hive receiver & theromostat with dual HW & CH controls to replace the existing Drayton HW & CH timer control and wired thermostat. I tried to set it all up last weekend and everything was going well until I tried to replace the thermostat. I set up the hive hub, changed the...

I've searched a lot for the answer to this question, so I thought I'd open it up here to see if anyone know how Hive actually works. I already have a Hive hub, and I'm now planning on using hive to control my heating. I only need to control heating as hot water is on demand (i.e there's no hot...

Hello all, I'm thinking of buying either Tado, Hive or Nest for my house. I live in a relatively new build 3 story townhouse in the UK with the Danfoss TP9000 thermostat / hot water programmer on the ground floor next to my Ideal Logic 15 boiler, a Danfoss TS2 sensor in the living room. Then...

i have Valiant Ecotech pro 24 ( 2011 ) model boiler and Hive dual receiver i wired up however heating wont switch off i assume its because of wiring and its not controlling boiler. my old relay box to wireless thermostat was wired up like picture attached. the Hive Reciever is wired up with...

Hi, I have purchased and attempted to install a Hive Gen 3. The existing set up was a thermostat (Drayton Tempus 7) and a WR 1 thermometer. Looking at the existing install and the wiring diagrams with the hive booklet I have assessed that I have an S-Plan configuration. So I have powered...

Hi all, I'm after a bit of advice and/or reassurance. I've recently had Hive installed (single channel receiver) via BG (British Gas) and it works very well, however, the concern I have is that the hot water has to be set to 'Continuous' via the switch on the left hand side of the boiler and...

Hello all, Probably my questions is weirdest you have seen. I have purchased a house last month and moved in. In this house we have a Baxi combi central heating. And I was given a Salus RT500RF Thermostat to control the heating. Now I want to replace this setup with Nest or hive and all my...

The above is a photo of my current Potterton wiring diagram. I’m trying to install a two channel Hive system. The issue i’m Having is with the live wire that runs into 5, can someone tell me what I should do with this? I’m sure I know what to do with the other wires but this is giving me a real...

Hi, I have an oil fed Geminox FCX 30c boiler (https://www.manualslib.com/products/Geminox-Fcx-30-C-4112227.html) which has REG 103 (FBR1) ambient thermostat connected to it (as well as an external probe thermometer) The boiler has a mains power cable that plugs into socket in boiler room and...

Hello, I had the bright idea to install a Hive system for my aging mother whilst cooking the turkey. Turkey is done, but not Hive. I have installed the hub and receiver. I haven't yet installed the thermostat. It is a gravity fed system. The problem is, I can't switch the receiver/controller to...

Hi All I've trawled through here and not found a thread that precisley matches my setup so rather than break rules and tag onto other posts have started this one! Has anyone got any experience wiring the hive single channel heating system to a glowworm 38cxi combi? I currenlty just have a...