Johnysmall said:
Fast track?
Let me tell you my story.
I am 38 years old.
I am an apprentiship trained mechanical engineer, who found work drying up due to computerised machines taking over the skilled sector of my trade.
I consider myself to be intelligent, confident and a quick learner. I decided to take the plunge 4 years ago, jacked my job in and became a plumbers apprentice. My first work was with two guys who worked price fitting heating systems for the council. Long hours, hard work, I learned quite a bit as to how a heating system worked in the year I was working for them...but nowhere near enough yet to fit a system on my own.
From there I went to work for a plumbing firm who gave me a van, an apprentice, responsibilities and a wide range of plumbing jobs to get me valuable experience in the trade. I also worked with heating engineers on their jobs and soaked up all the info I could.
During this time I attended college 1 day a week for 18 months and gained my level 2 NVQ heating and vent certificate. I completed this 6 months early as I explained before, I learn quick.
I immediately applied to do my ACS gas course which cost about £2,000 and consisted of 1 year, 1 day a week at college studying GAS.
Simple? No, far from it.
It's fair to say I have found it pretty hard to absorb all the information required to pass this course, there is a lot to learn, and this is being made harder and harder all the time to pass.
I am sitting here now revising my a**e off, I came into this forum trying to get a few bits of information I was not sure about and saw this thread, so I had to post.
My assessment starts Monday...I am told it could last 4 days and I am not the usual confident person I have been all my life in situations like this. I should pass because I have put so much into it.
FAST TRACK? DON'T EVEN THINK ABOUT IT.
Here are a few of the questions they will be asking...
Gas ACS
CCN1 – Assessment questions
Correct answers in bold.
1. Which of the Gas Safety Regulations compels the operative to use a temporary continuity bond where necessary?
a) Regulation 5.
b) Regulation 10.
c) Regulation 18.
d) Regulation 26.
2. The first priority when dealing with gas escape is:
a) Find the escape.
b) Carry out a tightness test.
c) Safeguard property.
d
) Safeguard life.
3. Gas Safety (Installation and Use) Regulation 36 places the responsibility to act safely when discovering gas escapes upon:
a) Transco personnel only.
b) All gas operatives.
c) All members of the public.
d
) Anyone within a, b and c.
4. What is the approximate volume of air required to completely burn 5 m3 of natural gas?
a) 15 m3.
b) 25 m3.
c)
50 m3.
d) 100 m3.
5. Which of the following is the minimum concentration of carbon monoxide within the air that will cause occupants to fall victim to coma within a few minutes?
a) 0.05%.
b)
0.4%.
c) 0.8%.
d) 1.0%.
6. The ventilation requirement for open flued appliances is dependant upon:
a)
Heat input.
b) Heat output.
c) Room dimension.
d) Flue height.
7. When pipework is buried beneath the groundused for pedestrian traffic, it should be buried at least:
a) 20 mm below the surface.
b) 30 mm below the surface.
c)
40 mm below the surface.
d) 50 mm below the surface.
8. A gas escape from the breather hole of a regulator indicates:
a) Faulty spring.
b) Bent spindle.
c)
Split diaphragm.
d) Worn valve seating.
9. What of the following equipment must be used to pin point the source of a gas escape?
a) A match
b) A cigarette lighter
c) Diluted washing up liquid.
d)
Leak detector solution.
10. If the correct warning notice is not fitted to a primary meter, the gas operative must inform the:
a) The occupier and/or landlord.
b) The gas supplier.
c)
The gas transporter.
d) There is no need to notify anyone.
11. The handle on an emergency/meter control valve must always:
a)
Fall to the off position.
b) Fall to the on position.
c) Be electrically insulated.
d) Have a 180o travel.
12. Range rated appliances must incorporate which component within their design?
a) A fan pressure sensor.
b) A constant pressure governor.
c) An air sending device.
d) A re-ignition device.
13. What is the likely fault if a cooker burner extinguishes after a period of approximately 15 minutes?
a) Faulty flame supervision device.
b) Blocked oven injectors.
c)
Blocked oven thermostat by-pass.
d) Undergassing causing incomplete combustion.[/b]