texecom

Hi everyone Recently installed a Texecom Premier Elite Ricochet system, previously always fitted Galaxy panels where you can quick set by pressing A) Is there a way of enabling this on the premier panel so the user doesn’t have to enter their code to set the panel? Many thanks in advance Matt

Hi, looking for some advice / help... have finally finished installing a Premier Elite 24 (poly) with texecom keypad, odyssey x-be bell box and just 4 zones (2 mag & 2 pir). powered it all up today and keypad and bell box all initially did as I was expecting but I can’t seem to get into...

Hi all, First post! Firstly thanks for all the advice people have previously posted on here, it has been incredibly helpful in the past! I have just installed my first Texecom Elite 24. All appears to be working fine, however I am having an issue when installing internal extension speakers! I...

I have an issue with a tamper alarm on my wireless external sounder. Yesterday in the middle of the day the alarm went off on the keypad whilst alarm not set. After silencing it it told me I had a tamper alarm on the external sounder. After resetting it happened again at about 9pm. I checked...

In Wintex i have an option for each zone to configure a chime tone. There are 4 options, silent and chime tone 1,2 &3 no matter which of the three chimes i select the keypad and alarm unit only ever chime the same tones. Are the three different chime settings suppose to omit a different tone?

Hi folks, I have a Texecom Premier 24 panel that i put in a few years ago and am now adding a second wired RKP for the garage - with a Premier PIR and a CQR 517 magnetic door contact to install. Can anyone advise how to wire these into the RKP's zones to pass through? I just can't get them...

Hi, I am trying to set my Texecom Premiere Elite so that i can use the tag to set the alarm but the alarm can only be unset by entering a valid user code (not via a tag). I have a key box nearby the alarm panel where everyones keys are stored, each persons keys has their own tab for the alarm...

Hi All, Starting a new thread after reading people experiencing similar issues to those described here: https://www.diynot.com/diy/threads/texecom-connect-smartcom-problem.523131/page-2#post-4629270 After some building works which included powering off the texecom for a couple of months and...

Premier Elite 88 Premier Elite AMQD Having an intermittent problem with arming. It seems to be linked to the zone that looks towards the keypad and one of the entrance doors. The zone in question is set to Guard/Access. Any ideas why this setup could be causing the arming problems? Thanks

I have a simple 16ohm speaker wired in to the aux+ and speaker- terminals, it works for warning sounds etc. But won't sound in the event of an alarm trigger. Checked the volume is up in the settings which it is, what am I doing wrong or if there another issue?

Hi sorry this is probably a noob question, I have the premier elite 64 with the smartcom setup. Smartcom connects to 2 serial ports and shows up in the communication options panel on com port 1 and com port 2. neither has an IP address, comport 1 (smartcom) is dhcp wifi I believe, I was just...

Hi, hoping someone can help me, I had to move my wintex and ricochet to a new machine. I have wintex running and connecting to my premier elite 64 no problem, but, if when connected through wintex i hit the ricochet button it just wont connect the bottom left "status" flashes a load of stuff...

Hi all. I have a self installed Texecom Premier Elite 64 W system complete with Smartcom remote control module hard wired to my network. I recently wanted it to auto disarm in the mornings just before we get up due to forgetfulness and noisy accidents! As part of this change I also split the...

Hello, Texecom Premier Elite 88 Texecom Premier Elite LCDLP Can someone please point me in the direction of how to configure some zones to chime but only within a specified time frame? I would like to have some door contacts chime only between 6pm and 6am, outside of that time there should be...

Just wondering if anyone else has experienced same issue. I fitted a premier elite wireless system just over 3 years ago. After about a year I had a battery fault on the internal sounder. Took the 8 lithium batteries out and tested them 7 were at 1.7v or above, one was 0.1v. Now after...

I have a Texecom Premier Elite 64W system and use a number their microshock wireless detectors on my windows. Over the last week, two of the detectors have given us what appear to be false alarms overnight after the system has been set overnight. The issue seems to occur after a long time of...

Hi all I have recently purchased the texecom premier elite kit 002 for my house. It has the 64W v5 control panel. I have watched a couple of youtube videos how to get the sensors registered onto the system bu my panel is not behaving the way the video shows. I have the commissioning jumper...

Just bought a Texecom Premiere Elite 24 kit - Panel, 5 x PIR, Bell/Sounder, Extension speaker, battery, Premier LCD-P Prox Keypad, Premier COM2400 Communicator and 5 x prox fobs. There is zero by way of instructions/manuals. Texecon site looks like you have to be a registered installer to...

Hello alarm gurus, I have never installed an alarm system before but I am looking forward to giving it a shot. I have put quite a lot of thought into how we would like the system to work and I believe I have chosen a system that is capable of meeting these requirements but I would like to get...

I have a Texecom 64-W panel (inbuilt wireless expander) that i've factory reset. The NVM erase counts down, and I go through the initial setup (language, default wireless, learn ricochet). When attempting to learn a device the panel simply makes one beep and does not initiate a 20 second...